LOADCENTER MAIN LUG INDR 125A

Indoor flush or surface mount with door
Box is significantly smaller and lighter while maintaining optimum wire-bending space
Side mounted main breaker allows top or bottom feed
Sturdy copper bus and galvanized box increase durability and reliability tinplated for corrosion resistance
Minimum 100% neutral terminations
All neutral holes are rated for 14 - 4 AWG wire
Extruded neutrals are easier to wire, reducing installation time and cost
Combination slotted/Robertson screws speed wiring

Powermark gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. at the same time, they deliver obvious and significant advances in design, function and quality.

SWITCH AC DISC OUTDR 2P 3W 60A

Used to mount two duplex receptacles on a box in surface mount application. Raised 1/2 in. 6-1/2 cu-in capacity. 4 in square. UL listed.

Grounding terminal screw standard. Combination switch with additional switch has 120/277 V rating, ideal for fluorescent lighting fixtures typical in commercial applications. 0.050 in thick steel mounting strap zinc-plated for corrosion resistance. Break-off provision for wiring both devices on same circuit or on separate circuits. Terminal screws backed out and ready for wiring. Side wire terminals accept up to #10 solid or stranded wire. Combination slot/Phillips head mounting and terminal screws. Switches meet all UL 20 requirements. UL Listed.

RACO OCT BOX COVER FLAT 4X1/2

Two 1/2 in and two 3/4 in conduit knockouts (sides). Two 1/2 in and two 3/4 in conduit knockouts (bottom). No bracket. Can be used in the installation of ceiling or wall lighting fixtures or as a junction box. Not designed for ceiling fan support. 50 lb maximum recommended static load. Acceptable for use in 2 hrs fire rated walls. UL listed. UPC bar code.

Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for exposed work or surface mount applications. Combination cover screw heads provide for faster mud ring/cover installation. Twelve 1/2 in conduit knockouts (sides). Four 1/2 in conduit knockouts (bottom). No bracket. 4 in square x 1-1/2 in deep and 21 cu-in capacity. UL listed, acceptable for use in 2 hrs fire rated walls. UPC bar code.

Designed to enclose electrical wiring, switches, receptacles or lighting fixtures. Constructed from 1/16 in pre-galvanized steel. 8-32 cover mounting screws assembled.

Steel box cover with single 1/2 in knockout in the center. 4 in square. Angled mounting slots allow for correction of box misalignment. UL listed.

Used to close outlet box. For mounting switch or receptacle. Size 4 in x 4 in, steel, UL listed.

Used to close outlet box. For mounting switches or receptacles. Size 4 in, UL listed.

Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2 hrs rated walls. Six 1/2 in knockouts (sides). Two 1/2 in knockouts (ends). Two 1/2 in knockouts (bottom). 4 in x 2 in x 1-7/8 in. 13 cu-in capacity. UL listed.

For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode.

Gardner Bender provides a complete line of staple and fastening solutions for all industries, including industrial, residential, construction or manufacturing. From low voltage wire to service entrance cables, professionals rely on Gardner Bender for quality fastening products.

Commonly used in Volkswagen, VW, Subaru, Suzuki, Porsche, Saab, Nissan, New Mini, Volvo, Toyota, Range Rover, Land Rover, Jeep, Chrysler, Hyundai, Jaguar, Honda, BMW, Audi, Kia and Ford, always replace the battery in the key even if dead to preserve settings, non-rechargeable.